 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| ALUMINUM ELECTROLYTIC CAPACITORS WG Chip Type, Low Impedance series Chip type, operating over wide temperature range of to - 55 ~ +105C. Designed for surface mounting on high density PC board. Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). UD Low Impedance WG Low Impedance WF Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current tan Performance Characteristics - 55 ~ +105C 6.3 ~ 50V 1 ~ 1500F 20% at 120Hz, 20C After 2 minutes' application of rated voltage, leakage current is not more than 0.01CV or 3 (A) , whichever is greater. Measurement frequency : 120Hz, Temperature : 20C Rated voltage (V) tan (MAX.) 6.3 0.26 10 0.19 6.3 2 4 16 0.16 10 2 4 25 0.14 16 2 3 35 0.12 25 2 3 50 0.12 Measurement frequency : 120Hz Stability at Low Temperature Rated voltage (V) Z- 25C / Z+20C Impedance ratio Z- 55C / Z+20C ZT / Z20 (MAX.) 35 2 3 50 2 3 Endurance After 1000 hours' application of rated voltage at 105C, capacitors meet the characteristic requirements listed at right. Capacitance change Within 20% of initial value tan 200% or less of initial specified value Leakage current Initial specified value or less Shelf Life Resistance to soldering heat Marking After storing the capacitors under no load at 105C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250C Capacitance change Within 10% of initial value for 30 seconds. After removing from the hot plate and restored Initial specified value or less tan at room temperature, they meet the characteristic requirements Leakage current Initial specified value or less listed at right. Black print on the case top. Chip Type Type numbering system (Example : 10V 100F) Positive C0.2 B0.2 0.5 MAX. (f4 ~ 6.3) Capacitance 105C Marking Voltage fD0.5 Plastic platform 0.3 MAX. UWG 1 A 1 0 1 M C L 1 G S Taping code fD code 4 ~ 6.3 GB 8 10 GS Configuration fD Capacitance tolerance (20%) 4 ~ 6.3 code CL 8 (6.2L) CL Rated Capacitance (100F) Rated voltage (10V) 8 (10L) 10 NL Series name Type (mm) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Lot No. L +0.1 -0.2 H C0.2 B0.2 Negative Positive 0.5 MAX. E A0.2 A0.2 H C0.2 0.5 MAX. Negative Positive (f8 6.2 ) Capacitance 105C Marking Trade mark Voltage fD0.5 Plastic platform 0.3 MAX. X2P 100 10V Lot No. L0.3 Plastic platform 0.3 MAX. fD0.5 A0.2 A0.2 X2P 100 6V E fD (f8 10, Capacitance 105C Marking Trade mark f10 10 ) Voltage L Lot No. Voltage mark for 6.3V is 6V . L0.5 Pressure relief vent H Dimension table in next page. A0.2 A0.2 X2P 220 25V B0.2 A B C E L H 4 5.4 5 5.4 6.3 5.4 8 6.2 8 10 10 10 3.2 2.9 3.3 2.4 2.1 1.8 10.3 8.3 8.3 6.6 5.3 4.3 10.3 8.3 8.3 6.6 5.3 4.3 4.5 3.1 2.3 2.2 1.3 1.0 10 10 6.2 5.4 5.4 5.4 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.5 ~ 0.8 0.8 ~ 1.1 0.8 ~ 1.1 E Negative CAT.8100V ALUMINUM ELECTROLYTIC CAPACITORS WG Cap. (F) series Dimensions V Code 6.3 10 16 0J 4 x 5.4 5 x 5.4 6.3 x 5.4 6.3 x 5.4 8 x 6.2 8 x 10 3.0 1.8 1.0 1.0 0.4 0.3 60 5 x 5.4 95 140 140 230 450 10 x 10 10 x 10 10 x 10 0.15 0.15 670 670 10 x 10 8 x 6.2 8 x 6.2 8 x 10 1A 4 x 5.4 5 x 5.4 1.8 95 6.3 x 5.4 8 x 6.2 0.4 0.4 0.3 0.15 0.15 230 230 450 670 670 10 x 10 10 x 10 10 x 10 10 x 10 8 x 6.2 1C 3.0 1.8 1.0 0.4 0.4 0.15 0.15 0.15 0.15 60 95 140 230 230 670 670 670 670 10 22 33 47 68 100 150 220 330 470 680 1000 1500 100 220 330 470 680 101 151 221 331 471 681 102 152 Cap. (F) V Code 25 35 50 1E 4 x 5.4 4 x 5.4 4 x 5.4 4 x 5.4 4 x 5.4 6.3 x 5.4 6.3 x 5.4 8 x 6.2 8 x 10 8 x 10 10 x 10 10 x 10 10 x 10 3.0 1.0 1.0 0.4 0.3 0.3 0.15 0.15 0.15 60 140 140 230 450 450 670 670 670 10 x 10 10 x 10 10 x 10 5 x 5.4 5 x 5.4 6.3 x 5.4 8 x 6.2 8 x 6.2 1V 3.0 3.0 3.0 3.0 1.8 1.8 1.0 0.4 0.4 0.15 0.15 0.15 60 60 60 60 95 95 140 230 230 670 670 670 6.3 x 5.4 8 x 6.2 8 x 10 10 x 10 10 x 10 10 x 10 Case size D x L (mm) 1H 4 x 5.4 4 x 5.4 4 x 5.4 5 x 5.4 5.0 5.0 5.0 3.0 2.0 0.7 0.6 0.3 0.3 0.3 Impedance 1 2.2 3.3 4.7 6.8 10 22 33 47 68 100 220 330 470 010 2R2 3R3 4R7 6R8 100 220 330 470 680 101 221 331 471 30 30 30 50 70 120 300 500 500 500 Rated ripple Max. Impedance () at 20C 100kHz Rated Ripple (mArms) at 105C 100kHz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.35 120 Hz 0.50 300 Hz 0.64 1 kHz 0.83 10 kHz~ 1.00 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please select UJ(p.76) series if high C/V products are reqired. Please refer to page 3 for the minimum order quantity. CAT.8100V |
Price & Availability of UWG1E220MCL
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |